产品详情

为了防止泰州INA轴承金属表面被水腐蚀，须对机床进行充分的润滑，并对机床的重要部件进行润滑。

In order to prevent the metal su-ce of INA bearing in Taizhou from being corroded by water, it is necessary to lubricate the machine tool adequately and lubricate the important parts of the machine tool.

当泰州INA轴承机器停止工作时，用切削液清洗机器表面，打开机器的保护盖，以分散机器工作区域内的潮湿空气。为防止电蚀的发生，应在金属表面涂覆一层防水油脂。这是不够的，以加强机床接地。为了避免的滋生和繁殖，应定期清洗或更换切削液，及时去除切屑，用软水（低矿物含量的纯水）稀释浓缩切削液。

When Taizhou INA bearing machine stops working, clean the machine su-ce with cutting fluid and open the protective cover of the machine to disperse the moist air in the working area of the machine. To prevent the occurrence of electric erosion, a layer of waterproof grease should be coated on the metal su-ce. This is not enough to enhance the grounding of machine tools. In order to avoid breeding and reproduction, cutting fluid should be cleaned or replaced regularly, chips should be removed in time, and cutting fluid should be diluted and concentrated with soft water (pure water with low mineral content).

除了泰州INA轴承的质量太硬，还属于非常密的部件，这两种高性能的轴承，如果使用不当，不但不能达到预期的性能，而且容易损坏轴承，须注意润滑。

In addition to Taizhou INA bearing quality is too hard, but also belongs to very dense components, these two high-performance bearings, if used improperly, not only can not achieve the desired performance, but also easy to damage the bearings, we must pay attention to lubrication.

在使用和安装时，应注意不要有强烈的冲击力，不要有垂直连接的丝锥轴承，不要让压力通过滚动元件。

When using and installing, care should be taken not to have strong imPACt force, no vertically connected taper bearings, and no pressure passing through rolling elements.

使用泰州INA轴承适当准确的安装工具，尽量使用专用工具，尽量避免使用布料和短纤维等物品。

Use appropriate and accurate installation tools for Taizhou INA bearings, use special tools as far as possible, and avoid using cloth and staple fibers as far as possible.

保持轴承及其周围环境尽可能清洁。即使不可见的微笑灰尘进入轴承，它也会增加轴承的磨损、振动和噪音。

Keep bearings and their surroundings as clean as possible. Even if the invisible smile dust enters the bearing, it will increase the wear, vibration and noise of the bearing.

防止轴承腐蚀

Preventing bearing corrosion

当用手直接取出泰州INA轴承时，须彻底清洗手上的液体，并在操作前涂上高质量的矿物油。在雨季和夏季，应特别注意防锈。在一定条件下，轴承的寿命比传统轴承的寿命长，特别是在轻载条件下。这些特殊的操作条件是，当滚动表面（轨道和滚动部件）被润滑油膜分离时，污染物可能引起表面损伤。事实上，在理想条件下，所谓的轴承寿命是可能的。

When taking out Taizhou INA bearing directly by hand, the liquid on the hand should be thoroughly cleaned and high quality mineral oil should be coated before operation. In the rainy season and summer, special attention should be paid to rust prevention. Under certain conditions, the life of bearings is longer than that of traditional bearings, especially under light load conditions. These special operating conditions are that contaminants may cause su-ce damage when the rolling su-ce (track and rolling parts) is separated by lubricating oil film. In fact, under ideal conditions, the so-calLED bearing life is possible.

文章来自：泰州SKF轴承 www.wh-skf.com

The article is from: Taizhou SKF bearing www.wh-skf.com

文章来自：泰州INA轴承 www.ina-china.cn

The article is from: Taizhou INA bearing www.ina-china.cn

文章来自：泰州NSK轴承 www.klbbearings.com

The article is from: Taizhou NSK bearing www.klbbearings.com

QQ：524085168

电话：0510-81207777

手机：13311666672